1966 Ford Mustang Fastback 289 C code Automatic Rust Free!

1966 Ford Mustang Pony Description

1966 Ford Mustang Fastback
VIN #: 6F09C212744Body: 63BColor: KTrim: 26Date: 04AD.S.O.: 21Axle: 6Trans: 6
This Mustang is an original "C" code 289 V8 fastback that has essentially receiveda "nut and bolt" full restoration over the last five years. The car was media blasted and received new floors, quarters, doors, fenders, hood, valances, tail panel, deck lid, suspension, interior, wiring harness, weatherstripping, and pretty much nearly every new part or piece of chrome you can purchase from Scott Drake or NPD. (see below). The important fiberglass interior panels, fold down seat, and trap door are all original uncut Ford pieces. The car runs and drives and does not appear to be leaking. It currently has a four barrel intake and Edlebrock 4V carb. The car has "pony" interior seats and door panels. Literallyevery nut and bolt was removed during this restoration. The floors are spotless. An HEI electronic distributor was installed to replace the points distributor. It has a clear Arizona title in my name and is located in Payson Arizona.
History: This restoration was the labor of love of an elderly gentleman who was unable to quite finish the job due to health concerns. I bought the car from his family and purchased and installed the door glass, vent windows, and a few odds and ends to get the car to where it is now. I have driven it around town a bit, but not very long distances and would not feel comfortable driving it acrosscountry without thoroughly checking it out first. It starts easily and run smoothly. I assume the engine and transmission were rebuilt, but I don’t have documents regarding this work. At this time I would like to sell it as I'm being stationed overseas and do not want it to sit. I would say it is 99% complete with a few things that could be done to make it 100%
The flaws: The Gentleman who did the restoration for the most part did a quality job, but reached the limits of his abilities with this car. The base/clear steel blue metallicpaint job has a few flaws, namely there are a few spots where the base coat is a little light. Additionally some masking tape was left on the car for a very long time and when I removed it, it pealed the paint on the lower rocker on the drivers side and a little on the upper front valance. (this could easily be covered with rocker moldings) The car has been color sanded in spots and could use a good buff to really make it shine. Personally, I'm fine with the paint the way it is, but I wanted to share everything I know about it. The welding work on the floors and body panels is solid, but not show quality. Also because most the pieces are aftermarket, the door/fender gaps are not perfect. The fold down seat needs to be adjusted as it rubs on the fiberglass panel. The steering needs to be aligned. The wipers and heater motor are there and work but need to be plugged into the new harness. There is a small dent in the passenger door from when I had it towed to my house, but otherwise the car is very very straight and does not appear to have much if any body filler in it. The dual exhaust rattles a little and could use additional hangers at the back (included). Mostly, I have just run out of time to make it perfect before I leave overseas. I know this is a lot of money to pay for a car sight unseen, so please feel free to contact me with any questions you may have.
New Parts-Complete new Vent windows with weatherstrip gasket-door felt-door window tracks-door handles exterior-door handles interior (pony)-door handle shaft assemblies (pony)-Door weatherstripping-Drip rail moldings-Pony door panels with pull cups-Window winders-dash-Carpet-Speedometer cluster-Headliner-Pinch trim-front and rear window trim-Kick panels-Pony seats, with all the correct trim. (Seat tracks restored as well and seats slide perfectly)-Rockermolding-shift knob and shift surround-dual exhaust 2.5" with long tube headers-Front Marker lights-Rear reverselights-rear taillight assemblies-Gas cap-rear leaf springs, hangers, U-bolts-Front springs-Front upper control arms-Front lower control arms-Strut rods-Sway bar and bushings-Tie rods inner/outer drag link and steering system-Edlebrock carb/air filter-HEI distributor and Ford Racing wires.-ignition with pony key-trunk lock chrome-front and rear bumpers-fuel line-Brake lines-Brake cylinders (four)-Master cylinder (dual chamber)-Alternator-Fold down seat chrome-rear view mirror-Hundreds of stainless screws and bolts-Fender mud guards-Front and rear glass rubber.