1992 Land Rover Defender 90 Nardo grey soft top full leather interior

1992 Land Rover Defender Leather Description

This is a 1992 2.5 NA Diesel Nardo grey soft top

VIN NUMBER SALLDVAC7JA913251

Like many Land Rovers the chassis was starting to show its age so we have carried out a frame off restoration on this Defender.

Even thoughit would have been far easier and cheaper to replace the chassis with a galvanised chassis we decided not to as it is a matching chassis/Vin number/ original enginevehicle.

It is an ex MOD Defender 90 so is fitted with the 2.5 naturally aspirated engine. Please note these are not as powerful as TDI or V8 engines and this particular engine does smoke. We can change the engine at additional cost but if it is being exported to USA it is best to have the original engine for customs...

It has had upgraded Bilstein suspension set up to create a far superior driving experience.

It has had a full inside and out professional colour change to Nardo grey

Below we have separated out the upgrade parts from the restoration work carried out/ parts fitted.

Upgrade parts fitted:

Full Leather heated LRI low base Corbeaus with diamond quilting

Full Leather LRI arm rest cubby box

4X Inward facing diamond stitch rear seats

Black leather sun visors

Momo steering wheel

LRI front carpet set

Rear load area rubber matting kit

Heavy duty black hood stick set and windscreen top rail kit

Black mohair canvas hood with side windows

16" gloss black Nemesisalloy wheel with 265 75 BFG KM2 tyres

Full exterior LED light set

JW speaker LED headlights

Best of British front grille and vent set

Smoked side wing repeaters

Gloss black wing mirrors

Quad DRL heavy duty bumper with fog lights

Stainless steel bolt set

Ebony SVX style side runner bars

Black textured steering guard

Heritage limited edition mud flaps

New Genuine Land Rover black badge kit

Genuine Land Rover TDCI/PUMA bonnet

Bilstein suspension shock set inc steering damper

Full vehicle superpro bush kit

Stainless steel front carpet retainers

Stainless steel rear mat retainer

New springs front and rear

Aircon style front grille nose cone

Restoration work carried out:

Investigate engine fault

- water in oil. Remove cylinder head, pressure test found a core plug leaking, replace leaking core plug, reface cylinder head. Replace cylinder head with new gaskets. Replace engine oil and filter. (this had to be done twice to flush system,)

(The above work has been carried out but as pointed out in the description the engine does smoke)

-Remove body from chassis for chassis work / refitting of body after chassis work

-Shot blast chassis, radius arms, axles and chassis mounting brackets

-Remove suspension bushes and refit with supplied superpro bushes

-Etch prime and paint Axle, radius arms and suspension brackets

-Repair chassis bulkhead out riggers and replace rear x member

-Etch prime and paint chassis in satin black 2k top coat

-Replace full exhaust system inc. new bushes & u-bolts

-Replace fuel tank (labour for swapping over tank fittings)

-Clean and prep under body for paint

-Paint under body in etch primer and satin black 2k top coat

-Strip clean / paint swivel housing and clean and paint rear brakes

-Bulkhead foot well repair to O/S lower panel

-Replace all suspension / some chassis and all body mounting bolts

-Drain fuel system of, replace fuel filter

-Pair of new front doors

-New door bolts and gaskets

-Windscreen rubber seal

-New door seals

Restoration parts Fitted *More parts may have been fitted than shown on list below.

-SUSPENSION/CHASSIS BOLTS

-FUEL FILTER - NA/TD 7

-OIL FILTER - NA/TD/TDI/V8

-HEAD GASKET SET - 2.5NA

-EXHAUST MOUNTINGS

-EXHAUST SYSTEM - 90 2.5NA

-FUEL TANK - 90 >WA

-REAR CROSSMEMBER FITTING KIT - GENUINE

-REAR CROSS MEMBER WITHOUT EXTENSIONS.

On site AA or RAC inspections are welcome.